VALVE LOCATION – Sporlan discharge bypass valves. (DBV) can be installed in of hot gas condensing in the bypass line (especially on remote systems). ble, contact Sporlan Division, Parker Hannifin for further suggestions. APPLICATION. Sporlan Hot Gas Bypass valves provide a precise meth- od of compressor. Find great deals for Sporlan Adrhe/80/85k Discharge Hot Gas Bypass Valve Shop with confidence on eBay!.
|Country:||Republic of Macedonia|
|Published (Last):||5 November 2013|
|PDF File Size:||4.16 Mb|
|ePub File Size:||15.81 Mb|
|Price:||Free* [*Free Regsitration Required]|
For instance, if you want to maintain a suction pressure of 60 psi in the evaporator, perform the following steps. I’m trying to understand how the hot gas bypass works. You will need an interface to set up this valve, an Allen key will not suffice. The electronic valve can also be piped to the evaporator inlet or the suction line. For example, if sporlan hot gas bypass return air in a system is close to set point, regardless of what that set point is, the suction pressure will be lower than if the return air was five degrees above set point, correct?
sporlan hot gas bypass
I’m a controls engineer so I don’t have vast knowledge in refrigeration. I’m just trying to understand what kind of valve is used in this case.
If I may add to that, injecting hot gas after the expansion valve also maintains refrigerant velocity for proper oil return to the compressor. The only reason I can think of for using after-evap HG injection is convenience of installation. Hot gas bypass valves can be used in many different applications where the load on the evaporator varies, from yot, to server sporlan hot gas bypass, to process cooling equipment.
Sporlqn this issue have been ga none-issue if you had cooled the floor of the tank? The hot gas bypass valve opens putting a false load on the evaporator, since the evaporator temperature has been increased, the supply air serving sporlan hot gas bypass lecture hall will also be increased preventing set point to be reached.
Hot gas bypass question
PHM If I may add to that, injecting hot sporlan hot gas bypass after the expansion valve also maintains refrigerant velocity for proper oil return to the compressor. It’s 6t tank with 2x 5 HP compressors. Simulate a low load condition, allow the pressure to drop below 60 psi.
Building Science Discussions Pro’s Forum: The valve will maintain that set point by monitoring evaporator pressure and adding hot gas as needed. Can you think of any others?
Sporlan Hot Gas Bypass
How about injecting the hot gas at the evap exit but before the sensing bulb? Or just the drawings for it so far? Hot gas bypass valve. Dumping directly to suction doesn’t. Self contained walk in? Is it actually in the tank as a seperate item?
Originally Sporlan hot gas bypass by Poodle Head Mikey.
American Refrigeration Supplies
What are you wanting to accomplish? Results 1 to 13 of There are mechanical valves and electrical valves.
With increased evaporator temperature, set bypaas will take longer to achieve, thus increasing compressor run times all the while preventing evaporator freeze up. Ybpass a space or process temperature reaches set point, hot gas can be added to the evaporator to raise its temperature.
Related Forums The sporlan hot gas bypass where Electrical professionals meet. The link sporlan hot gas bypass for Sporlan Bulletin will explain what they are used for, how they work and how they are applied: Electronic The electronic hot gas bypass valve EHGB uses the same concept as it’s mechanical counter part but operates a little differently.
If you use hot gas bypass, the expansion valve remains nearly at full load all the time, so an EEV wouldn’t be of much advantage except if you needed closer control Above that setpoint it starts to close down and above that setpoint starts to open up. Does Air Balancing Save Energy? How is it made? Hot gas bypass question I’m trying to understand how the hot gas bypass sporlan hot gas bypass.
Is the tank existing? I ask because maybe there is an easier way to accomplish the same goal.
Sporlan Adrhe-6-0/80/85k6301 Discharge Hot Gas Bypass Valve 170066
The problem is for this specific case the flow of liquid into the tank is very slow and the tank should start cooling when the pillow plate evaporator of the tank is only partially covered so in order to avoid the formation of ice on sporlan hot gas bypass evaporator and very low pressure on the outlet of the evaporator there is a need to add some load. Hot gas bypass question. This is the one I found in the first place and one from Danfoss as well.
Originally Posted by icemeister. When setting up the valve, you may need to simulate a hhot load condition. Mechanical The mechanical hot gas bypass valve HGB is fed discharge gas hot gas teed off from the discharge line. Oil Burners Pro’s Forum: This prevents compressor short cycling with varying loads, compressor stops and starts are a major factor in compressor failure over sporlan hot gas bypass.
It’s divided in 4 parts. What does the evaporator look sporlaan Training and Education Pro’s Forum: All times are GMT I’m working on a bulk cooling tank.