This part can be programmed by Digi-Key; for details please contact our custom department at x or @ has a page-write capability for up to 16 bytes of data. The 24LC16B is available in the standard 8-pin DIP and both 8-lead and lead surface mount SOIC pack . 24LC16B-I/SN Microchip Technology EEPROM 2kx8 – V datasheet, inventory & pricing.

Author: Tuktilar Nikojora
Country: Jordan
Language: English (Spanish)
Genre: Travel
Published (Last): 6 December 2010
Pages: 159
PDF File Size: 5.37 Mb
ePub File Size: 19.56 Mb
ISBN: 529-4-74114-371-4
Downloads: 78722
Price: Free* [*Free Regsitration Required]
Uploader: Sajas

24LC16B-I/P | MICROCHIP | EEPROM | Online shop – Comet Electronics

Where none of the Micochip equivalents do address decoding at all. Voltage Comparator Design Their 01 and 02 devices actually have the three address bits decoded, the 04 device has two bits decoded, the 08 device just one, and the 16 device none at all.

244lc16b Thanks for your help! The PDP-8 used individual toggle switches to set each bit, then you pressed a spring loaded toggle switch to transfer the byte, then entered the rest of the program.

In these datasheets they also state that the address pins are not connected. Last edited by betwixt; 9th September at I am looking to have possible 4 sx’s set up as slaves, and 1 eeprom and one rtc all set up on the same i2c bus if thats possible.

Maximum power point in solar converter But I could successfully verify that the chips decode the status of the address pins. Blood oxygen meters, Part 1: This doesn’t mean that you couldn’t use more than 1 chip, simply that you cannot use the multiple IC2 address protocall. Maybe, this explains the difference. Changing a V capacitor in Cisco switch power adapter As the address following the control byte is only 8 bits wide, three additional bits are required to cover the full 2lc16b space of bytes.


Potentiometer with Microcontroller 3.

Initial value depending on the input Gunther, Page 11 of said datasheet states that A0, A1, and A2 are not connected in this device. I am curious where the 0xFF came from.

Microchip 24LC16B-I/SN, 16kbit Serial EEPROM Memory, 900ns 8-Pin SOIC I2C

Addressing of the devices is performed by sending a control byte via the bus. A 24CL16 with all three address pins connected to Vss would acknowledge the control byte x, and one with A0 connected to Vcc and A1, A2 connected to Vss would acknowledge the control byte x, etc.

I did not use the 24LC16 so far but “smaller” devices, like the 24LC I use the 24LC64 in some of my SX applications with no problems. The 24lc16n now is Nate, I was just curious, and got the ST datasheet for their 24C PORTD should show 0x34 at the conclusion.

24LC16B Serial EEPROM :: Solarbotics

First, I have to be able to send and receive eight bits. Review a datasheet to understand why this can’t work. SPI verilog testbench code 6. Sign In or Register 24c16b comment.


About Acknowledge function of 24LC16B

Hey, you can find the datasheet for the 24LC16 here: Quick Links Categories Recent Discussions. In this system, each of the SXes could act as master and slave, therefore I also had to handle bus arbitration but it worked nicely in the end.

Dual-channel DMM puts two 7. Mathematical formula of the minimum separations required between two patch antennas? As you can imagine, 24cl16b a long program was brutal.

Nate, this is strange. You either wait for the maximal expectable write time or perform ACK polling for actual finish of write action.

They definitely allow for eight devices on a bus, and they have two 244lc16b bytes following the control byte in order to address the full range of the memory. Part and Inventory Search. Quiery regarding cadence Fuse Amperage Determination Circuit Let’s say I have an sx set up as a 24lc61b on that same bus, and i would like to send some info to only the sx, I could set the address to some abritrary number, but the eeprom would answer to any address, correct?

Nate Post Edited Nate: